2000 Series Narrow Head Exit Devices and Trims are designed for new or retrofit installation into other manufacturers’ devices. Push Bar assembly’s smooth and reduced projection minimizes catch hazard. Device function is field selectable by adaptation with selected type of trim. A full complement of lever trim is available in wide range of architectural finishes. 2000 Series are made to comply with the highest safety and security standards in industry. Devices and trims are UL/cUL listed for Panic Hardware or Fire Hardware. They are certified to ANSI/ UL305 and ANSI/BHMA A156.3 Grade 1. 2000 Series provides superior durability for high impact applications such as offices, schools, banks, assisted living facilities and other institutions or commercial buildings.
The 2000 Series Narrow Head Exit Devices are fabricated and blended with simplicity, strength, durability, aesthetics and installer-friendly innovations.
Devices and trims are designed for new or retrofit installation into other manufacturers’ exit devices and trims.
Made to comply with the highest safety and security standards in industry.
UL/cUL listed for panic hardware or 3-hour fire rated exit hardware.
Certified to ANSI/UL305 and ANSI/BHMA A156.3 Grade 1.
A Special plastic inserts and rubber bumpers reduce noise and don’t fail under high or low temperatures. Impervious to petroleum lubricants.
B Detachable center case allows switching between mechanical and electrical options which replaces the need of buying two complete sets.
C Center Case with maximum versatility, Surface and Concealed Vertical Rods can be adjusted inside the center case with an ingenious rod holder design.
D Cross spindle offers additional strength.
E Replaceable cam breaks at predetermined load to prevent further damage of the trim mechanism. Handing change is simple and easy, just remove screw and cam from mechanism and rotate lever to desired position, then replace cam and fasten the screw.
F Center Case mounting plate made of heavy gauge steel adding extra strength.
G Stainless steel latch and deadlatching blade add perceived value.
H Stamped Center Case Cover made with any commercial finishes, fits minimum 2” stile.
I Steel die cast rocker arm designed for heavy loads.
J Push Bar is smoothly surfaced. Reduced projection minimizes catch hazard.
K Integrated End Cap and pivot add push pad stability and make the bar move smoothly regardless of where the pressure is applied on push pad.
L Dogging can be done with an allen wrench, a small flat key or a flat blade screwdriver.
M Flush End Cap design.
Device Material
2000 Series is furnished standard with grooved case. Smooth surface style is available. The two styles are mechanically and dimensionally identical and come with a wide selection of finishes.
Finishes
COLOR
ANSI/BHMA
US
B.E.G.
A.D.
C.F.H.
Polished Brass
605
3
Brass, Polished
Plated
Buffed Anodized
Satin Brass
606
4
Brass, Satin
Plated
Anodized
Polished Bronze
611
9
Bronze, Polished
Plated
Buffed Anodized
Satin Bronze
612
10
Bronze, Satin
Plated
Anodized
Dark Oxidized Satin Bronze
613
10B
Bronze, Satin; Dark Oxidized
Plated
Anodized
Polished Chrome
625
26
Brass, Polished & Plated
Plated
Buffed Anodized
Satin Chrome
626
26D
Brass, Satin & Plated
Plated
Anodized
Satin Stainless Steel
630
32D
St. Steel, Satin
Plated
Anodized
For other finishes consult factory.
Mechanism Case Options
Smooth
Grooved
Push Bar Trim Options:
Embossed “PUSH”
Braille, embossed “CAUTION STAIRWELL”
Red silk screen lettered “EMERGENCY EXIT ONLY – PUSH TO OPEN & SOUND ALARM”
Trims are furnished with wrought plate and extruded or with cast solid grips.
Trims are designed to retrofit into other manufacturers’ devices.
Trims are UL/cUL certified for ANSI/BHMA A156.3 Grade 1 and 3-Hour Fire Rated.
Trims are through bolted. (“GD” Grip furnished standard, unless specified).
Specify handing when ordering.
500 Series Escutcheon Features
Escutcheon and lever with sleek and seamless design produced by casting or forging.
Trims are designed to retrofit into other manufacturers’ devices.
Handing field reversible.
Trims are UL/cUL certified for ANSI/BHMA A156.3 Grade 1 and 3-Hour Fire Rated.
Specify lever or knob design. (“D” Lever furnished standard, unless specified).
Model 508 Operation Breakable Cam
Model 508 Key Locks or Unlocks Lever (For 08/11 Functions)
Model 508 Trim is composed of heavy duty investment cast steel. An internal breakable cam breaks away when a predetermined load is applied to the outside lever handle in locked mode without damaging the trim or compromising security. The cam is easily replaceable with minimum efforts.
The breakable cam is a replaceable part
Lever / Grip Options
Pull Trim
Escutcheon
Panic Application
Fire Application
Rim Device
P/N. 106 Rim Strike For Rim / SVR / 3PT top strike
P/N. 108 Rim Strike For double door Rim / 3PT use with F170/F270 mullion
P/N. 103 Rim Strike For Rim / 3PT
P/N. 136 Rim Strike For double door Rim / SVR / CVR combination with coordinator
P/N. 227/227F Bottom Strike Furnished standard for SVR / CVR / 3PT
P/N. 224 Bottom Strike Optional for SVR / 3PT
Shim
P/N. 616819-010 For 106 Rim Strike Two (2) pieces furnished standard
P/N. 616819-030 For 108 Rim Strike Two (2) pieces furnished standard
P/N. 616819-050 For CVR top & bottom latches Strike Sixteen (16) pieces furnished standard for Top and Bottom latches. Eight (8) pieces furnished standard for LBR
P/N. 618619-010 For 103 Rim strike Two (2) pieces furnished standard
P/N. 618619-020 For 203 Strike Two (2) pieces furnished standard
Cylinders are not furnished standard with the device or trim, specify when required. Schlage C keyway, 6-pin standard, available in 630 or 626 finish. Small Format Interchangeable Core combinated/uncombinated also available. Specify type and finish when ordering.
Cylinder Cam
Cylinder Type
Applications
Trim
Cylinder
Cyl. Length
(Part/No.)
Cylinder Cam
Mortise Cylinder
08 / 11 for
RIM/SVR/CVR/3PT
500
Standard
1-1/8″ (441-102)
440-0704
I/C
1-1/4″ (442-601)
440-0708
Cylinder Dogging
All Device
Standard
1-1/4″ (441-103)
440-0702
I/C
1-3/8″ (442-701)
440-0706
Rim Cylinder
03 for
RIM/SVR/CVR/3PT
(Must use with Cylinder Guard Part/No.611824-020 )
400
Standard / I/C
Tailpiece Length 3-1/8″ (79.6mm)
03 / 09 / 12 for
RIM/SVR/CVR/3PT
500
Illustration
Dimension
X=1/4″ (6mm)
Y=5/8″ (15mm)
X=3/8″ (9.5mm)
Y=3/4″ (19mm)
X=1/4″ (6mm)
Y=5/8″ (15mm)
X=3/8″ (9.5mm)
Y=3/4″ (19mm)
Cam No.
440-0702
440-0704
440-0706
440-0708
Cylinder Guard
611824-020 For use on 403R
I/C Core “A” keyway standard supplied. Specify 6 or 7 pin, combinated or uncombinated and finish 606 or 626 when ordering. Consult factory for other keyways.
Dogging
LD
CD
HKD
ED
Less Dogging
Less Dogging is available in all 2000 Series panic exit devices.
Cylinder Dogging
Available for all models except for Fire Exit Hardware. Cylinder Dogging provides the ability to lock down the Push Bar with a key cylinder, allowing the door to be used in both Push/ Pull mode. To order, specify “CD”. Requires the use of a 1-1/4″ Mortise Cylinder (not furnished standard).
Flat/Hex Key Dogging
Electrical Dogging
Mullions
Mullions
Removable mullions are used with paired doors where
a full width opening is only occasionally required. Doors
are fitted with Rim Exit Devices and normally function
as single doors. Available in 7′, 8′
or 10′ (2134mm, 2438mm or 3048mm) lengths.
Model 170 / F170 Keyed Removable Mullion
Top and Bottom Fittings:
Investment cast steel, furnished with steel anchors for floors.
Mullion:
2″ x 3″ (609mm x 915mm) steel.
Stock size:
8′ (2438mm) length standard, can be cut for opening less than 8′ (2438mm).
10′ (3048mm) length available upon request.
Finishes:
600, 689, 695.
UL Listed:
Listed for 3-Hour Fire Rated Exit Hardware.
Cylinder:
Not furnished standard, keying is standard 1-1/8″ (28.5mm) Mortise Cylinder with cam.
Specify with or without strikes when ordering.
The head design of 170/F170:
Provides a secure, quick and easy means of removal. The Mullion can be installed and locked without using key.
Model 270 / F270 Non-Keyed Removable Mullion
Top and Bottom Fittings:
Investment cast steel, furnished with steel anchors for floors.
Mullion:
2″ x 3″ (609mm x 915mm) steel.
Stock size:
8′ (2438mm) length standard, can be cut for opening less than 8′ (2438mm).
10′ (3048mm) length available upon request.
Finishes:
600, 689, 695.
UL Listed:
Listed for 3-Hour Fire Rated Exit Hardware.
Specify with or without strikes when ordering.
Top Rod
Illustration
Device No.
Part No.
Rod Length
2200
2500
(SVR/3PT)
616823-020
36-1/8″ (916mm)
616823-030
48-1/8″ (1221mm)
616823-030
Add
616823-040*
48-1/8″ (1221mm)
Add
24″ (609mm)
2300
(CVR)
616823-070
37″ (940mm)
616823-080
49″ (1245mm)
616823-080
Add
616823-050*
49″ (1245mm)
Add
23-7/8″ (605mm)
* Extension Rod
Bottom Rod
For Push Bar location at 39-5/8″(1006 mm) from finished floor.
Panic Application
Fire Application
Removable mullions are used with paired doors where
