Generic selectors
Exact matches only
Search in title
Search in content
Search in posts
Search in pages

CR Series Door Coordinators

Bar Coordinator

Patent No. 9,476,240 B1

CR-32 / CR-42 / CR-52 / CR-60 / CR-72

Klacci’s CR Series Bar Coordinators offer a simple yet effective way of regulating double door entries. These products guarantee a correct order of door closing and prevent that any entry that is not properly closed may cause a safety concern in case of emergency.

Features

  • The lever mechanism on the active door side holds the active door open until a trigger mechanism releases it when the passive door closes.
  • An adjustable override mechanism allows the active door to close first in case that an excessive force is applied on it to protect the door as well as the coordinator from further damage.
  • These units are compatible with flush bolts, door closers and other double door hardware for a more complete application.

Certification/Compliance

  • Conforms to ANSI/BHMA A156.3 Type 21A (Grade 1).
  • UL/cUL Fire Rated for 3-Hour Fire Door Hardware, conforms to UL10C.

Bar Coordinator Length

  • The bar coordinator standard length should be equal to the active door’s width (X) plus 1/2 the inactive door’s width (Y).
  • For cases where above condition cannot be met, the bar coordinator length must be at least 6″ (152.4 mm) longer than the active door width (X).
  • The bar coordinator length must not exceed the overall frame opening between stops (O).
    Note: Standard stop thickness (S) is of 5/8″ (15.9 mm).

Note: Standard stop thickness (S) is of 5/8″ (15.9 mm).

Examples:

  • Active door width (X): 42″ (1066.8 mm)
    Inactive door width (Y): 42″ (1066.8 mm)
    Recommended coordinator: CR-60
  • Active door width (X): 36″ (914.4 mm)
    Inactive door width (Y): 18″ (457.1 mm)
    Recommended coordinator: CR-42

Cutout Type Ordering Information

Bar coordinators may require an additional cutout in order to use with surface or concealed vertical rod exit devices. Please check the following chart for the type of cutout needed:

Cutout TypeDoor TypeExit Device ModelLatch BacksetLatch TypeDoor application
A-TypeMetal DoorFor Klacci:
1300/F1300
F2300
2-3/4"
(69.9 mm)
Plunger Release
Pair of 30" (762.0mm) Doors (For CR-42)
Pair of 36" (914.4mm) Doors (For CR-52)
Pair of 42" (1066.8mm) Doors (For CR-60)
Pair of 48" (1219.2mm) Doors (For CR-72)
Pair of 56" (1422.4mm) Doors (For CR-72)
Pair of 60" (1524.0mm) Doors (For CR-72)

For VON DUPRIN:
98/9947
98/9948-F
33/3547
33/3548-F
B-TypeWood DoorFor Klacci:
2300
1-5/16"
(33.3 mm)
Plunger Release
For VON DUPRIN:
98/9947WDC
98/9947WDC-F
33/3547WDC
33/3547WDC-F
C-TypeMetal DoorFor VON DUPRIN:
8847-F
5547-F
2-3/8"
(60.3 mm)
Plunger Release Bracket

Note: No applicable cutout type for CR-32.

If the product model or door application is not listed on the chart or a different latch backset dimension is used, please provide the following information when ordering:

  1. Exit device’s product model and manufacturer’s template.
  2. Active door width (X)
  3. Inactive door width (Y)
  4. Latch backset (L)
  5. Stop thickness (S) if other than 5/8″ (15.9 mm)
  6. Opening between stops (O)

Material

Aluminum

Size

ModelLengthWidthHeight
CR-3232" (812.8 mm)1-5/8" (41.3 mm)5/8" (15.9 mm)
CR-4242" (1066.8 mm)1-5/8" (41.3 mm)5/8" (15.9 mm)
CR-5252" (1320.8 mm)1-5/8" (41.3 mm)5/8" (15.9 mm)
CR-6060" (1524.0 mm)1-5/8" (41.3 mm)5/8" (15.9 mm)
CR-7272" (1828.8 mm)1-5/8" (41.3 mm)5/8" (15.9 mm)

Finishes

628 (US28)
Satin Aluminum,
Clear Anodized
707 (US3)
Bright Brass
Anodized
711 (US19)
Flat Black
Anodized

Filler Bar

FLB-20 / FLB-32 / FLB-48

Features

The filler bar can be used to fill the gap between the end of the bar coordinator and the inactive door’s stop for more pleasant aesthetics.

Ordering Information

The table below shows the standard matching between the bar coordinator and the filler bar.

If other lengths are required please specify before ordering.

Door WidthBar Coordinator ModelFiller Bar Model
Pair of 24" (609.6mm) Doors CR-32FLB-20
Pair of 30" (762.0mm) Doors CR-42FLB-20
Pair of 36" (914.4mm) DoorsCR-52FLB-20
Pair of 42" (1066.8mm) DoorsCR-60FLB-32
Pair of 48" (1219.2mm) Doors CR-72FLB-32
Pair of 56" (1422.4mm) DoorsCR-72FLB-48
Pair of 60" (1524.0mm) Doors CR-72FLB-48

Material

Aluminum

Size

ModelLengthWidthHeight
FLB-2020" (528 mm)1-5/8" (41.3 mm)5/8" (15.9 mm)
FLB-3232" (812.8 mm)1-5/8" (41.3 mm)5/8" (15.9 mm)
FLB-4848" (1219.2 mm)1-5/8" (41.3 mm)5/8" (15.9 mm)

Finishes

628 (US28)
Satin Aluminum,
Clear Anodized
707 (US3)
Bright Brass
Anodized
711 (US19)
Flat Black
Anodized

Mounting Bracket

MB-1F / MB-2F / MB-3F

Features

The mounting bracket can be installed along with fire-rated hardware, such as parallel arm closers and surface vertical rod exit devices, used for stop mounted hardware to be properly installed without damaging the bar coordinator.

Note: Stop mounted hardware will need to be lowered to compensate for the height of the Bar Coordinator and Mounting Brackets.

Material

Steel

Size

ModelLengthWidthHeight
MB-1F4" (101.6 mm)3" (76.2 mm)1-5/8" (41.3 mm)
MB-2F4" (101.6 mm)4" (101.6 mm)1-5/8" (41.3 mm)
MB-3F4" (101.6 mm)3-1/2" (88.9 mm)1" (25.4 mm)

Finishes

689 (US28)
Aluminum
Painted
600 (USP)
Primed for
Painting

Gravity Coordinator

Patent No. 8,595,980 B1

CR-07 / CR-09

Features

  • The gravity coordinator is applied on pair doors to allow the inactive door to close before the active door.
  • Nylon and rubber rollers provide quiet and efficient operation and help protect the doors from damage.

Certification/Compliance

  • Conforms to ANSI/BHMA A156.3 Type 21B (Grade 2).
  • UL/cUL Fire Rated for 3-Hour Fire Door Hardware, conforms to UL10C.
Astragal Location
Without Carry Open BarWith Carry Open Bar
CR-07CR-09CR-07CR-09
ANo Astragal1'6" ~ 4'0"
(457.2 mm ~
1219.2 mm)
2'6" ~ 4'0"
(762 mm ~
1219.2 mm)
1'6" ~ 2'6"
(457.2 mm ~
762 mm)
2'6" ~ 4'0"
(762 mm ~
1219.2 mm)
BPull Side, Active Door (Standard)
CPush Side, Inactive Door1'6" ~ 3'4"
(457.2 mm ~
1016 mm )
2'6" ~ 4'0"
(762 mm ~
1219.2 mm)
N/AN/A
DB + C

Note: Astragal Overlap: 3/4″ (19.1mm) – Standard.

Material

Brass

Size

ModelProjection
CR-077" (177.8 mm)
CR-099" (228.6 mm)

Finishes

626 (US26D)
Satin Chrome
613 (US10B)
Dark Oxidized
Satin Bronze

Carry Open Bar

COB

Features

  • When the inactive door is opened, the carry open bar provides the automatic opening of the active door as well.
  • The carry open bar cannot be installed along with flush bolts.
  • Door coordinator accessory for fire-rated application.

Certification/Compliance

  • Conforms to ANSI/BHMA A156.3 Type 21 (Grade 1).

Material

Stainless Steel

Finishes

630 (US32D)
Satin Stainless
Steel
613 (US10B)
Dark Oxidized
Satin Bronze

Headquarters and Operation Office

I-TEK Metal Manufacturing Co., Ltd.

Global Office

KLACCI Inc.

BHMA, UL, Intertek
Generic selectors
Exact matches only
Search in title
Search in content
Search in posts
Search in pages

Copyright© 2019 – I-TEK Metal Manufacturing. All rights reserved.