Generic selectors
Exact matches only
Search in title
Search in content
Search in posts
Search in pages

2000 Series Narrow Head Exit Devices

2000 Series Narrow Head Exit Devices and Trims are designed for new or retrofit installation into other manufacturers’ devices. Push Bar assembly’s smooth and reduced projection minimizes catch hazard. Device function is field selectable by adaptation with selected type of trim. A full complement of lever trim is available in wide range of architectural finishes. 2000 Series are made to comply with the highest safety and security standards in industry. Devices and trims are UL/cUL listed for Panic Hardware or Fire Hardware. They are certified to ANSI/ UL305 and ANSI/BHMA A156.3 Grade 1. 2000 Series provides superior durability for high impact applications such as offices, schools, banks, assisted living facilities and other institutions or commercial buildings.

The 2000 Series Narrow Head Exit Devices are fabricated and blended with simplicity,
strength, durability, aesthetics and installer-friendly innovations.

  • Devices and trims are designed for new or retrofit installation into other manufacturers’ exit devices and trims.
  • Made to comply with the highest safety and security standards in industry.
  • UL/cUL listed for panic hardware or 3-hour fire rated exit hardware.
  • Certified to ANSI/UL305 and ANSI/BHMA A156.3 Grade 1.

A Special plastic inserts and rubber bumpers reduce noise and don’t fail under high or low temperatures. Impervious to petroleum lubricants.

B Detachable center case allows switching between mechanical and electrical options which replaces the need of buying two complete sets.

C Center Case with maximum versatility, Surface and Concealed Vertical Rods can be adjusted inside the center case with an ingenious rod holder design.

D Cross spindle offers additional strength.

E Replaceable cam breaks at predetermined load to prevent further damage of the trim mechanism. Handing change is simple and easy, just remove screw and cam from mechanism and rotate lever to desired position, then replace cam and fasten the screw.

F Center Case mounting plate made of heavy gauge steel adding extra strength.

G Stainless steel latch and deadlatching blade add perceived value.

H Stamped Center Case Cover made with any commercial finishes, fits minimum 2” stile.

I Steel die cast rocker arm designed for heavy loads.

J Push Bar is smoothly surfaced. Reduced projection minimizes catch hazard.

K Integrated End Cap and pivot add push pad stability and make the bar move smoothly regardless of where the pressure is applied on push pad.

L Dogging can be done with an allen wrench, a small flat key or a flat blade screwdriver.

M Flush End Cap design.

Device Material

2000 Series is furnished standard with grooved case. Smooth surface style is available. The two styles are mechanically and dimensionally identical and come with a wide selection of finishes.

Finishes

COLORANSI/BHMAUSB.E.G.A.D.C.F.H.
Polished Brass6053Brass, PolishedPlatedBuffed Anodized
Satin Brass6064Brass, SatinPlatedAnodized
Polished Bronze6119Bronze, PolishedPlatedBuffed Anodized
Satin Bronze61210Bronze, SatinPlatedAnodized
Dark Oxidized Satin Bronze61310BBronze, Satin; Dark OxidizedPlatedAnodized
Polished Chrome62526Brass, Polished & PlatedPlatedBuffed Anodized
Satin Chrome62626DBrass, Satin & PlatedPlatedAnodized
Satin Stainless Steel63032DSt. Steel, SatinPlatedAnodized

For other finishes consult factory.

 

Mechanism Case Options

Smooth
Grooved

Push Bar Trim Options:

  • Embossed “PUSH”
  • Braille, embossed “CAUTION STAIRWELL”
  • Red silk screen lettered “EMERGENCY EXIT ONLY – PUSH TO OPEN & SOUND ALARM”
ANSI/BHMA
Number
OperationsTrim OptionCylinder Application
400 Series
Thumbpiece
500 Series
Escutcheons
Rim Cyl.Mortise Cyl.
01Exit Only401NNN
02Dummy Pull Only402502NN
03Night Latch, Key Retracts Latch Bolt403R503RYN
08Key Locks or Unlocks Latch BoltN508MNY
09Night Latch Key Retracts Latch BoltN509RYN
11Key Locks or Unlocks Latch BoltN511MNY
12Night Latch Key Retracts Latch BoltN512RYN
14Lever Always Active, No CylinderN514NN
16Turn Always Active, No CylinderN516NN

Note: Suffix R/M represent cylinder application type.

400 Series Pull Trim Features

  • Trims are furnished with wrought plate and extruded or with cast solid grips.
  • Trims are designed to retrofit into other manufacturers’ devices.
  • Trims are UL/cUL certified for ANSI/BHMA A156.3 Grade 1 and 3-Hour Fire Rated.
  • Trims are through bolted. (“GD” Grip furnished standard, unless specified).
  • Specify handing when ordering.

500 Series Escutcheon Features

  • Escutcheon and lever with sleek and seamless design produced by casting or forging.
  • Trims are designed to retrofit into other manufacturers’ devices.
  • Handing field reversible.
  • Trims are UL/cUL certified for ANSI/BHMA A156.3 Grade 1 and 3-Hour Fire Rated.
  • Specify lever or knob design. (“D” Lever furnished standard, unless specified).

Model 508 Operation Breakable Cam

Model 508
Key Locks or Unlocks Lever
(For 08/11 Functions)

Model 508 Trim is composed of heavy duty investment cast steel. An internal breakable cam breaks away when a predetermined load is applied to the outside lever handle in locked mode without damaging the trim or compromising security. The cam is easily replaceable with minimum efforts.

The breakable cam is a replaceable part

 

Lever / Grip Options

Pull TrimEscutcheon
  Panic Application
  Fire Application

 

Rim Device

P/N. 106
Rim Strike
For Rim / SVR / 3PT top strike
P/N. 108
Rim Strike
For double door Rim / 3PT
use with F170/F270 mullion
P/N. 103
Rim Strike
For Rim / 3PT
P/N. 136
Rim Strike
For double door Rim / SVR / CVR
combination with coordinator
      

Vertical Rod Device

Top Strike

P/N. 215
Top Strike
For flush transom
SVR / 3PT
P/N. 216
Top Strike
For CVR
P/N. 203
Top Strike
For SVR / 3PT
    

Flat Bottom Strike

P/N. 225
Bottom Strike
Optional for
SVR / CVR / 3PT
round slide bolt
P/N. 226
Bottom Strike
Optional for
SVR / CVR / 3PT
round slide bolt
    

 

Bottom Strike

P/N. 227/227F
Bottom Strike
Furnished standard for
SVR / CVR / 3PT
P/N. 224
Bottom Strike
Optional for
SVR / 3PT
    

Shim

P/N. 616819-010
For 106 Rim Strike
Two (2) pieces furnished standard
P/N. 616819-030
For 108 Rim Strike
Two (2) pieces furnished standard
P/N. 616819-050
For CVR top & bottom latches Strike
Sixteen (16) pieces furnished standard
for Top and Bottom latches. Eight (8)
pieces furnished standard for LBR
P/N. 618619-010
For 103 Rim strike
Two (2) pieces furnished standard
P/N. 618619-020
For 203 Strike
Two (2) pieces furnished standard

Cylinders are not furnished standard with the device or trim, specify when required. Schlage C keyway, 6-pin standard, available in 630 or 626 finish. Small Format Interchangeable Core combinated/uncombinated also available. Specify type and finish when ordering.

 

Cylinder Cam

Cylinder TypeApplicationsTrimCylinderCyl. Length
(Part/No.)
Cylinder Cam
Mortise Cylinder
08 / 11 for
RIM/SVR/CVR/3PT
500Standard1-1/8″ (441-102)440-0704
I/C1-1/4″ (442-601)440-0708
Cylinder DoggingAll DeviceStandard1-1/4″ (441-103)440-0702
I/C1-3/8″ (442-701)440-0706
Rim Cylinder
03 for
RIM/SVR/CVR/3PT
(Must use with Cylinder Guard Part/No.611824-020 )
400Standard / I/CTailpiece Length 3-1/8″ (79.6mm)
03 / 09 / 12 for
RIM/SVR/CVR/3PT
500
Illustration
DimensionX=1/4″ (6mm)
Y=5/8″ (15mm)
X=3/8″ (9.5mm)
Y=3/4″ (19mm)
X=1/4″ (6mm)
Y=5/8″ (15mm)
X=3/8″ (9.5mm)
Y=3/4″ (19mm)
Cam No.440-0702440-0704440-0706440-0708

Cylinder Guard

611824-020
For use on 403R

I/C Core
“A” keyway standard
supplied. Specify 6 or
7 pin, combinated or
uncombinated and
finish 606 or 626 when
ordering. Consult factory
for other keyways.

Dogging

 LD

 CD

 HKD

 ED

Less Dogging


Less Dogging is available in all 2000 Series panic exit devices.

Cylinder Dogging


Available for all models except for Fire Exit Hardware. Cylinder Dogging provides the ability to lock down the Push Bar with a key cylinder, allowing the door to be used in both Push/ Pull mode. To order, specify “CD”. Requires the use of a 1-1/4″ Mortise Cylinder (not furnished standard).

Flat/Hex Key Dogging

Electrical Dogging

Mullions

Mullions

 Removable mullions are used with paired doors where
a full width opening is only occasionally required. Doors
are fitted with Rim Exit Devices and normally function
as single doors. Available in 7′, 8′
or 10′ (2134mm, 2438mm or 3048mm) lengths.

Model 170 / F170
Keyed Removable Mullion

Top and Bottom Fittings:

Investment cast steel, furnished with steel anchors for floors.

Mullion:

2″ x 3″ (609mm x 915mm) steel.

Stock size:

8′ (2438mm) length standard, can be cut for opening less than 8′ (2438mm).
10′ (3048mm) length available upon request.

Finishes:
600, 689, 695.

UL Listed:

Listed for 3-Hour Fire Rated Exit Hardware.

Cylinder:

Not furnished standard, keying is standard 1-1/8″ (28.5mm) Mortise Cylinder with cam.
Specify with or without strikes when ordering.

The head design of 170/F170:

Provides a secure, quick and easy means of removal. The Mullion can be installed and locked without using key.

Model 270 / F270
Non-Keyed Removable Mullion

Top and Bottom Fittings:

Investment cast steel, furnished with steel anchors for floors.

Mullion:

2″ x 3″ (609mm x 915mm) steel.

Stock size:

8′ (2438mm) length standard, can be cut for opening less than 8′ (2438mm).
10′ (3048mm) length available upon request.

Finishes:
600, 689, 695.

UL Listed:

Listed for 3-Hour Fire Rated Exit Hardware.
Specify with or without strikes when ordering.

 

Top Rod

IllustrationDevice No.Part No.Rod Length
 2200
2500
(SVR/3PT)
616823-02036-1/8″ (916mm)
616823-03048-1/8″ (1221mm)
616823-030
Add
616823-040*
48-1/8″ (1221mm)
Add
24″ (609mm)
 2300
(CVR)
616823-07037″ (940mm)
616823-08049″ (1245mm)
616823-080
Add
616823-050*
49″ (1245mm)
Add
23-7/8″ (605mm)

* Extension Rod

Bottom Rod

For Push Bar location at 39-5/8″(1006 mm) from finished floor.

IllustrationDevice No.Part No.
 2200
2500
(SVR/3PT)
616823-010
 2300
(CVR)
616823-060

Coordinator

Coordinator

Gravity Coordinator

CR-07 / CR-09

  • The gravity coordinator is applied on pair doors to allow inactive door to close before active door.
  • Nylon and rubber rollers provide quiet and efficient operation and help protect the doors from damage.
  • Non-handed.
  • UL/cUL certified for ANSI/BHMA A156.3-2014 Grade 2 and 3-hour Fire Rated.
  • Finishes: 613, 626.

Bar Coordinator

CR-32 / CR-42 / CR-52 / CR-60 / CR-72

  • The bar coordinator is applied on pair doors to allow inactive door to close before active door.
  • All bar coordinator units function easily. The active door lever, located nearest to the active stop, holds the active door open until the trigger mechanism is released by the closing of the inactive door.
  • All bar coordinator units are equipped with an adjustable override feature which allows the active door to close first under extreme pressure.
  • All bar coordinator units are compatible with flush bolts.
  • Finishes: 613, 626, 630.

Carry Open Bar

COB

  • The carry open bar is applied on pair doors.
  • When the inactive door is opened, the carry open bar provides the automatic opening of the active door as well.
  • The carry open bar cannot be installed along with flush bolts.
  • Non-handed.
  • Finishes: 613, 626.
  • Klacci ANSI Grade 1 2000 Series Electrical Exit Devices

   Learn More   

Fire Door Applications and Listings

F2000 Series Narrow Head Fire Exit Devices
Maximum Door Opening Applications and Listings

Exit
Device
Door
Meterial
Single DoorDouble Door
With 170
mullion
With 270
mullion
VR/VR
Same Direction
VR/VR
Double Egress
F2100
RIM
Metal3 Hour
4′ x 8′
3 Hour
8′ x 8′
3 Hour
8′ x 8′
F2200
SVR
Metal3 Hour
4′ x 10′
3 Hour
8′ x 10′
3 Hour
8′ x 10′
F2200
LBR
Metal3 Hour
4′ x 10′
3 Hour
8′ x 10′
3 Hour
8′ x 10′
F2300
CVR
Metal3 Hour
4′ x 10′
3 Hour
8′ x 10′
3 Hour
8′ x 10′
F2300
LBR
Metal3 Hour
4′ x 10′
3 Hour
8′ x 10′
3 Hour
8′ x 10′
F2500
3PT
Metal3 Hour
4′ x 8′
3 Hour
8′ x 8′
3 Hour
8′ x 8′

4′ (1219mm), 8′ (2438mm), 10′ (3048mm)

Notes:

  1. Fire Exit Device conforms to UL10C and UBC7-2.
  2. Fire Exit Device is applicable for wood door with 1-1/2 Hour or 1/3 Hour rating.
  3. Consult with door manufacturer for specific limitations on Fire Door Assemblies.

Single Door

Rim Exit Device / Vertical Rod Exit Devices
PanicRIM2100Up to 4′ x 10′ Door Size
SVR2200
CVR2300
3PT2500
Fire (3 Hour)RIMF2100Up to 4′ x 8′ Door Size
SVRF2200Up to 4′ x 10′ Door Size
CVRF2300
3PTF2500Up to 4′ x 8′ Door Size

Double Egress Opening

Two Surface Vertical Rod Devices
PanicSVR x SVR2200 x 2200Up to 8′ x 10′ Door Size
Fire (3 Hour)SVR x SVRF2200 x F2200
Two Concealed Vertical Rod Devices
PanicCVR x CVR2300 x 2300Up to 8′ x 10′ Door Size
Fire (3 Hour)CVR x CVRF2300 x F2300

Double Egress Opening Less Bottom Rod

Two Surface Vertical Rod Devices Less Bottom Rod
PanicSVR x SVR2200LBR x 2200LBRUp to 8′ x 10′ Door Size
Fire (3 Hour)SVR x SVRF2200LBR x F2200LBR
Two Concealed Vertical Rod Devices Less Bottom Rod
PanicCVR x CVR2300LBR x 2300LBRUp to 8′ x 10′ Door Size
Fire (3 Hour)CVR x CVRF2300LBR x F2300LBR
Note: Fire Rated Door with Auxiliary Fire Bolt.

Two Rim Exit Devices with Removable Mullion, Same Direction

Two Rim Exit Devices with Removable Mullion
PanicRIM x RIM2100 x 2100Up to 8′ x 10′ Door Size
Fire (3 Hour)RIM x RIMF2100 x F2100Up to 8′ x 8′ Door Size’
Two Three-Point Latching Devices with Removable Mullion
Panic3PT x 3PT2500 x 2500Up to 8′ x 10′ Door Size
Fire (3 Hour)3PT x 3PTF2500 x F2500Up to 8′ x 8′ Door Size’
Note: With 170 Keyed / 270 Non-Keyed Removable Mullion.

Two Vertical Rod Devices, Same Direction Less Bottom Rod
(Do not use overlapping astragal)

Surface Vertical Rod Devices Less Bottom Rod
PanicSVR x SVR2200LBR x 2200LBRUp to 8′ x 10′ Door Size
Fire (3 Hour)SVR x SVRF2200LBR x F2200LBR
Concealed Vertical Rod Devices Less Bottom Rod
PanicCVR x CVR2300LBR x 2300LBRUp to 8′ x 10′ Door Size
Fire (3 Hour)CVR x CVRF2300LBR x F2300LBR
Note: Fire Rated Door with Auxiliary Fire Bolt.

Two Vertical Rod Devices, Same Direction
(Do not use overlapping astragal)

Two Surface Vertical Rod Devices
PanicSVR x SVR2200 x 2200Up to 8′ x 10′ Door Size
Fire (3 Hour)SVR x SVRF2200 x F2200
Two Concealed Vertical Rod Devices
PanicCVR x CVR2300 x 2300Up to 8′ x 10′ Door Size
Fire (3 Hour)CVR x CVRF2300 x F2300

Vertical Rod Devices/ RIM Exit Devices, Same Direction

One Rim Exit Device x One Vertical Rod Device
PanicRIM x SVR2100 x 2200Up to 8′ x 10′ Door Size
RIM x CVR2100 x 2300
Fire (3 Hour)RIM x SVRF2100 x F2200
RIM x CVRF2100 x F2300

Headquarters and Operation Office

I-TEK Metal Manufacturing Co., Ltd.

Global Office

KLACCI Inc.

BHMA, UL, Intertek
Generic selectors
Exact matches only
Search in title
Search in content
Search in posts
Search in pages

Copyright© 2019 – I-TEK Metal Manufacturing. All rights reserved.